CAM-391
The belt is overflowing and material is falling to the ground
Mid-afternoon at the aggregates plant. The belt feeding the crusher is loaded beyond its width, and at the change of run the material spills over the side and pours down. Below, a heap of stone has built up that already reaches the height of the structure. Two workers in hi-vis vests are standing near the heap. IRIS sees material outside the belt and starts timing from the moment it began to fall.
Turn on IRIS Vision
AI-generated image
What IRIS understands
What it recognises in this scene
- material falling off the belt
- heap built up under the belt
- belt loaded beyond its width
- worker under the belt
- second worker beside the heap
What this camera measures
An alert says something is happening. The reading says how much.
- 9 minTime material has been falling
- 2People under the belt
- 1,2 mHeight of the heap against the column
- 4Spills counted at this point this week
- 14:05Time of the first material outside
The figures on this screen are an example from the illustration, not any client's measurement.
The rule
You decide once. IRIS applies it always.
If
material falls outside the belt for more than a minute
Then
- alert the plant supervisor with the belt, the point and the time
- save the video from the first material to spill over
- count the people under the belt at that moment
The instruction that set it up«Tell me when material falls off the belt at the transfer point, and how long it has been falling.»
What changes
What changes for whoever answers for the plant
A spill like this is cleared with a shovel and hours of work, and it is usually noticed only when the heap is already in the way. With the alert as it happens, the supervisor knows which belt, which point and the minute material started falling, and can act before the heap reaches the rollers. And there is a count: how many times that same point spills in a month. A point that spills every week is not bad luck, it is something to fix.
What people usually ask
Does IRIS know why the belt is overflowing?
Not on its own. The camera sees that material is spilling, where it spills and from what minute. If the cause is in front of the lens — a collapsed roller, a torn skirt, a jam at the transfer — it shows on the video. If it is inside the machine, it does not. IRIS provides the image and the time; the diagnosis is made by maintenance.
Can you count how many spills a point has?
Yes. Every alert is stored with its belt, its point and its time, so at the end of the month there is a number for each transfer point. That turns a corridor complaint into data you can take to a meeting and sort worst first. Counting is what a camera does best, and here it is what pays for the repair.
Does the belt have to be stopped for IRIS to see it?
No. The camera watches the belt while it runs and sees material falling off as it happens. Nor does IRIS stop anything: it sends the alert with the image, and whether to cut the feed, stop the belt or wait for the shift change is decided by a person at the plant.
Other cameras
- CAM-380 · A loaded truck leaves by a way that is not a way out
- CAM-381 · Dark material going into the bay for pale aggregate
- CAM-382 · Good ore heading for the waste dump
- CAM-383 · A bucket of grey gravel on top of the wrong stockpile
- CAM-384 · A boulder too big for the crusher mouth going in anyway
- CAM-385 · A tanker loading under the wrong silo
A different case every time
We won't just tell you. We'll show you.
It is a summary of the real screen: it plays by itself, step by step, and shows only the path of one case. The actual tool has far more than fits in here.
- Finds the plate
- Reads the characters
- Follows the same plate
Next step
What does a venue with twenty thousand people inside see?
15 cases: 11 raise an alert when something happens and 4 only measure. You see each image as it is, and then with what IRIS understands on top.
When does a bad review get decided?
15 cases: 11 raise an alert when something happens and 4 only measure. You see each image as it is, and then with what IRIS understands on top.
And the best part
You cannot describe a line with a sentence.You have to draw it on the image.
Asking is for finding; counting is for measuring. That is why the number comes out the same every day, and why people counting is certified by the Centro Español de Metrología.
Tell us your problem and we will say whether IRIS understands it, or not yet.
We reply the same working day.